Mountonus Brodit ProClip Mount Shop Logo
UK Trusted Supplier of Brodit ProClip Mount and Car Cradle Holder Solutions.

Brodit Car Holder Mount Catalog

Part No: Brodit 215371
Product Type: Brodit Pipe Mount With Tilt Swivel
Product Fits:
Placement:
Price: £ 45.04
Description:
Fits diameter 19-30 mm. Face plate angled 45°.
Technical Information:
For installation of devices on pipes and stays, for example all kind of vehicles, on motorcycles, boats, carts, stands, wheelchairs, airplanes etc. The mount has a 45° angle face plate which is attached onto a tilt swivel. This means you can adjust your device in order to get it in a better position/angle. The mount fits pipes with diameter 19-30 mm. Made in black plastic.
More Info Add to Shopping Cart
Part No: Brodit 861638
Product Type: Brodit Mounting Equipment
Product Fits:
Placement:
Price: £ 106.24
Description:
Double sided adhesive tape. 25 mm. 15 m/roll.
Technical Information:
Extra strength adhesive tape. Width: 25 mm. 15 meters per roll.
More Info Add to Shopping Cart
Part No: Brodit 215396
Product Type: Brodit Table Stand
Product Fits:
Placement:
Price: £ 26.37
Description:
With rounded foot. With face plate with predrilled holes.
Technical Information:
Keep you mobile phone within easy reach in the office as well as home! You can attach any holder to the stand.
More Info Add to Shopping Cart
Part No: Brodit 945070
Product Type: Brodit Adapter Cable
Product Fits:
Placement:
Price: £ 10.38
Description:
Molex 4 Pin adaptor to DC, 4mm.
Technical Information:
Length of cable: 175cm (connector heads not included).
More Info Add to Shopping Cart
Part No: Brodit 240411
Product Type: Brodit Mounting Accessories
Product Fits:
Placement:
Price: £ 4.44
Description:
Gap opener tool, big.
Technical Information:
A tool that makes installations easier, used e.g. to press into gaps in the interior in order to widen them. With thin ends, one pointy and one level end. Manufacutred in black ABS plastic. 30x195x5 mm.
More Info Add to Shopping Cart
Part No: Brodit 213050
Product Type: Brodit Monitor Mount
Product Fits:
Placement:
Price: £ 22.04
Description:
Mounting plate with Tilt Swivel, centered. Low
Technical Information:
Smaller, lower face plate. The choice for an adjustable monitor angle. Fits monitors with a vertical slot in back.Install onto ProClip.
More Info Add to Shopping Cart
Part No: Brodit 215342
Product Type: Brodit Pipe Mount With Tilt Swivel
Product Fits:
Placement:
Price: £ 42.36
Description:
Motorcycle mount with tilt swivel plate, predrilled AMPS holes. 31,8 mm diameter.
Technical Information:
Motorcycle mount, is to be installed on the handle bar. To be used for installation of a PNA, GPS device, PDA etc.

The mount is equiped with a tilt swivel, so you can adjust the device in order to avoid light reflection. The face plate has predrilled holes (AMPS-standard).
More Info Add to Shopping Cart
Part No: Brodit 215099
Product Type: Brodit Mounting Accessories
Product Fits:
Placement:
Price: £ 19.18
Description:
Note-pad holder with tilt swivel.
Technical Information:
Holder for note pad, with tilt swivel. Attach onto ProClip Mounting Platform. (Note pad and pen are not included.)
More Info Add to Shopping Cart
Part No: Brodit 215559
Product Type: Brodit MoveClip
Product Fits:
Placement:
Price: £ 17.66
Description:
MultiMoveClip, 4 screws. High strength. With release button.
More Info Add to Shopping Cart
Part No: Brodit 521621
Product Type: Brodit Active Car Cradle Holder With Cig-Plug
Product Fits:
Placement:
Price: £ 72.99
Description:
Adjustable holder with Micro-USB connector. Fits for devices with and without skin with the following dimensions: Width: 62-77 mm, Thickness: 9-13 mm. 2,1A charger. 12/24V. With tilt swivel.
Technical Information:
Keep your phone in a holder when on the road and you will always have it within easy sight and reach. Safe, comfortable and convenient! The active holder charges your phone when it is placed in the holder. If you have a car with USB interface, you can disconnect the cig-plug from the holder's cable in order to get a USB-cable to connect directly to the USB connector in your vehicle.
 
The adjustable holder fits for devices with and without skin with the following dimensions: Width: 62-77 mm, Thickness: 9-13 mm. Adjustable holders come in various sizes. Measure your device and compare with the holder specifications in order to make sure you have chosen the correct product (if you are using a skin: measure the device with the skin in place).
 
Before using the holder you need to confirm the charging cable is turned the right way (you can rotate it) and also set the holder's width so it suits your device, then your phone is held firmly in place in an upright position for maximum cellular reception. The holder has a neat and discreet design which blends well with the vehicle's interior.
 
The holder is made of black ABS plastic. It is easy to put the device into the holder, and just as easy to take it with you when leaving the vehicle. The holder is equipped with a tilt swivel so you can adjust the angle of your device in order to avoid light reflection on the screen. You can tilt the holder 22° in each direction. Attach onto ProClip Mounting Platform.

This product supports Qualcomm QC 2.0 quick charge (provided the device supports Qualcomm QC 2.0 quick charge).
More Info Add to Shopping Cart
Part No: Brodit 215436
Product Type: Brodit Mounting Plate
Product Fits:
Placement:
Price: £ 13.56
Description:
Extension plate, 155x50x5mm. With predrilled holes.
Technical Information:
The extension plate makes it possible to attach two devices with tilt swivel
onto the same ProClip, e.g. a GPS device holder as well as a mobile phone holder. With predrilled holes, made of black ABS plastic. Size: 155x50x5mm.
More Info Add to Shopping Cart
Part No: Brodit 521620
Product Type: Brodit Active Car Cradle Holder With Cig-Plug
Product Fits:
Placement:
Price: £ 72.99
Description:
Adjustable holder with Micro-USB connector. Fits for devices with and without skin with the following dimensions: Width: 62-77 mm, Thickness: 6-10 mm. 2,1A charger. 12/24V. With tilt swivel.
Technical Information:
Keep your phone in a holder when on the road and you will always have it within easy sight and reach. Safe, comfortable and convenient! The active holder charges your phone when it is placed in the holder. If you have a car with USB interface, you can disconnect the cig-plug from the holder's cable in order to get a USB-cable to connect directly to the USB connector in your vehicle.
 
The adjustable holder fits for devices with and without skin with the following dimensions: Width: 62-77 mm, Thickness: 6-10 mm. Adjustable holders come in various sizes. Measure your device and compare with the holder specifications in order to make sure you have chosen the correct product (if you are using a skin: measure the device with the skin in place).
 
Before using the holder you need to confirm the charging cable is turned the right way (you can rotate it) and also set the holder's width so it suits your device, then your phone is held firmly in place in an upright position for maximum cellular reception. The holder has a neat and discreet design which blends well with the vehicle's interior.
 
The holder is made of black ABS plastic. It is easy to put the device into the holder, and just as easy to take it with you when leaving the vehicle. The holder is equipped with a tilt swivel so you can adjust the angle of your device in order to avoid light reflection on the screen. You can tilt the holder 22° in each direction. Attach onto ProClip Mounting Platform.

This product supports Qualcomm QC 2.0 quick charge (provided the device supports Qualcomm QC 2.0 quick charge).
More Info Add to Shopping Cart
Part No: Brodit 240902
Product Type: Brodit Mounting Plate
Product Fits:
Placement:
Price: £ 23.08
Description:
Monitor mount for Vesa, with tilt swivel. Fits 75mm and 100mm.
More Info Add to Shopping Cart
Part No: Brodit 511626
Product Type: Brodit Passive Car Cradle Holder With Tilt Swivel
Product Fits:
Placement:
Price: £ 88.21
Description:
Adjustable holder. Fits devices without skin. Width: 226-309 mm. Height: 151-226 mm.
Technical Information:
With your surfpad in a holder attached in your car you will always have it within easy reach. Safe, neat and convenient! You can connect e.g. a charging cable to the surfpad when it is in the holder. The holder is mounted onto a tilt swivel so you can adjust the angle and switch between portrait and landscape mode.
 
Features
The adjustable holder fits for devices with the following dimensions: Width: 226-309 mm, Height: 151-226 mm. Measure your device and compare with the holder specifications in order to make sure you have chosen the correct product. Before using the holder you set the size to fit with your device. The holder is designed with the intention to leave as much space open as possible for connection of charging cables and/or headphones.
 
Important
Tablets should not be installed onto a car’s dashboard if they block the view or block key controls. The ProClip is designed for installation of smaller devices (phones), not for large devices (tablets). If you want to place a tablet onto the car’s dashboard, each combination of tablet-car must be examined in detail by you in order to determine if such an installation is possible in the specific case. Consideration should be given to the position and how firmly the ProClip is in place, as well as the size of the tablet you wish to use. Brodit will not give any recommendations for such installations.
 
An installation of a tablet onto a vehicle’s dashboard is always done on the customer’s own responsibility. Brodit recommends to use tablets on the car’s headrest, installed onto a Brodit headrest mount.
More Info Add to Shopping Cart
Part No: Brodit 511848
Product Type: Brodit Passive Car Cradle Holder With Tilt Swivel
Product Fits:
Placement:
Price: £ 62.94
Description:
Adjustable holder. Fits devices with or without skin/case, with height 120-150 mm, max thickness 25 mm.
Technical Information:
Adjustable passive holder with tilt swivel for devices with or without skin/case. This holder is crash tested and approved for use with device without skin/case on Brodit's headrest mount. Keep your device in a holder in your car and you will always have it within easy sight and reach. Safe, neat and convenient!
 
Measure your device/skin/case and compare with the holder specifications to choose the right product for you. This holder fits for devices with or without skin/case with the height 120-150 mm and maximum thickness 25 mm.

You can attach a charging cable to your device in order to get charging while in the holder. The holder is equipped with a tilt swivel and can easily be adjusted in order to avoid light reflection. Tilts 20° and swivels 360°. The upper and lower parts of the holder have padded cushions for protection against sliding and scratching. It is easy to place the device in the holder, and to take it with you when leaving the car. Mounting plate 42x50 mm with predrilled AMPS-holes +2x3,5 mm centered holes. Made of high grade black ABS/Acetal plastic. Made in Sweden
 
Crash tested:
This adjustable holder is crash tested according to standard for car seats (ECE R17). The crash test applies for a tablet that weighs 490 g. The tests have been performed on one seat with invisible headrest pins (type Volvo etc.) and one seat with visible headrest pins (type Ford etc.) in the forward and rearward directions. The adjustable holder keeps the tablet in place during all executed tests.
 
Dimensions: 145 x 129 x 69 mm (W x H x D mm)   
Weight: 157 g
 
Important information:
Tablets should not be installed onto a car’s dashboard. They may block the view or key controls and the ProClip is designed for installation of smaller devices (phones), not for large devices (tablets). If you want to place a tablet onto the car’s dashboard, each combination of tablet-car must be examined in detail by you in order to determine if such an installation is possible in the specific case. Consideration should be given to the position and how firmly the ProClip is in place, as well as the size of the tablet you wish to use. Brodit will not give any recommendations for such installations. An installation of a tablet onto a vehicle’s dashboard is always done on the customer’s own responsibility. Brodit recommends to use tablets in a holder on the car’s headrest, installed onto a Brodit headrest mount.
More Info Add to Shopping Cart
Catalog Pages: < Prev   1  2  3  4  5 [ 6 ] 7  8  9  10  11 ...23 Next >